• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How a Wood Burning Stove Works

Wood burning stoves can be an excellent addition to any home. However it is important to use them only with properly seasoned logs.

Older stoves with no secondary combustion admitted air below and above the fuel - this resulted in energy loss as well as chimney tarring and air pollution.

Modern wood stoves use superior combustion principles that splits the air supply into two stages. This enables greater efficiency in heating and lower emissions.

Efficient Combustion

The efficiency of combustion in your wood stove is a measurement of the speed at which your wood is transformed into heat. The efficiency of the heating transfer is the degree to which heat is transferred from your stove to the room. A wood-burning stove with high efficiency of combustion and heat transfer will use less fuel and produce less waste, including carbon monoxide, ash, and steam.

Modern wood stoves have a high efficiency in combustion, due to their sophisticated design. They can maximize the burning and use less wood. They also tend to emit low levels of emissions, especially stoves that are EPA-certified and require a catalytic combustor in order to remove exhaust gases after they leave the stove. These cleaner stoves are a good choice for homeowners who want to minimize their impact on the environment while still enjoying the warmth of a wood stove.

Proper operation and maintenance will improve the efficiency of your stove. The most important thing is to ensure the combustion process is controlled, which is accomplished by maintaining a fire in the stove with frequent additions of small pieces of wood regularly. This will prevent the accumulation of flammable creosote inside the chimney which can make the stove less efficient.

The efficiency of a wood stove is also affected by the use of dried and seasoned firewood that has less than 20 percent. Dry, seasoned firewood will not only produce more heat from the same fuel but will also produce less smoke and air pollution.

The Environmental Protection Agency (EPA) has set guidelines to limit the amount smoke and other pollutants a new stove may emit in an hour. To comply with the EPA guidelines, the majority of modern wood stoves rely on a secondary combustion process or catalytic combustor to manage combustion and reduce the amount of pollutants they emit. If you're looking to purchase a wood burning stove that complies with EPA emission standards, then search for one that has an EPA certification sticker. It should also have a smoke emission level lower than 4 grams per hour.

Catalytic Combustion

Catalytic woodstoves use a ceramic honeycomb combustor that is coated with noble metals, such as palladium or platin. The combustor 5829186 (5829186.xyz) operates in the same way as your car's catalyst does to clean your exhaust. When smoke passes through the combustor at high temperatures, the noble metals react with the particles and the chemicals in the smoke, breaking them down into harmless end products such as carbon dioxide and water.

This enables the stove to have lower emissions and burn more efficiently than non-catalytic models, without sacrificing the heat output or efficiency. The combustor performs its best when the gas temperature in the flue is 1000degF or higher. The combustor will not function properly if the fire is burned in a low-flame.

Burning foreign materials, such as paper logs, treated or painted wood, 5829186 may damage the combustor. The burning of these substances can result in "masking" which covers the cells of the combustor with a substance which prevents it from working in the way it was intended. Masking can also result from closing the bypass damper to shortly or refueling with wet wood. If the combustor cells have not been cleaned regularly of creosote, fly-ash and tar, a plugging could occur, which can cause smoke to spill out.

Properly operated and positioned the combustor will give years of reliable performance. It will require very little maintenance, other than cleaning off the soot from its surface after a long burn and then dusting it with a dry, soft bristled brush.

The combustor has a bypass damper which is opened to ignite a fire and closed to refill the stove. The bypass damper should be checked for the "operate catalyst" indicator that indicates if your combustor is operating within its optimal temperature range. The operating range of your combustor will be diminished if you open the bypass damper too soon. Closing the bypass too soon could reduce the temperature of the combustor's outlet and www.5829186.xyz cause damage. If you're not sure how to operate the bypass damper, consult your stove's instruction manual or contact our customer service department for assistance.

Airflow Controls

Air flow controls are essential to ensure that your wood stove burns safely and efficiently. The primary, secondary and tertiary air systems work together to allow your fire to burn effectively. Each system plays a unique function in the process of combustion.

The air control is situated beneath or inside the stove's door. It controls the amount air that enters the firebox. More air means a quicker-burning fire but it also increases the chances of creosote and chimney smokiness buildup. When you light your wood stove, the primary air control should be extended wide and for a short time.

Once you've reached the desired heat level, you can slowly close the air control that is primary until the desired heat is attained. The stove or chimney should not emit any smoke since this is a sign of the combustion is not efficient.

Secondary airflow controls are utilized to supply oxygen to your stove's top, usually as air jets that are placed above the fire. This is the most crucial aspect of controlling the flame. Without it, your fire will burn too fast and produce excessive amounts of smoke.

The secondary airflow, which is the final step in the airflow system of your stove, is fed into the chimney or updraft. This creates a strong draft in the flue, allowing your fire to function at its peak.

It is crucial to remember that your wood stove was built and optimized for burning wood that is firewood only. Any other type of burning combustible won't burn as well in your wood stove, and may result in high levels of emissions and possibly chimney fires. The best kind of combustion fuel is wood that has been dried for at minimum six months, but softwood is equally effective. Avoid using paper and cardboard since they could release toxic fumes or cause creosote and ash to build within your stove. It is also recommended to avoid placing logs or any other combustibles over your fire as they can explode.

Safety

Wood burning stoves can provide a cost-effective alternative heat source, especially if you live in an area that experiences frequent power outages. They can be dangerous when employed in a wrong manner. They can result in harmful chemical substances that can harm your health. They can also cause a fire hazard as well as carbon monoxide poisoning. You can avoid these dangers by taking a few simple precautions.

Use only clean, dry wood for your stove. Never make use of gasoline, kerosene or charcoal starter fluid to ignite or ignite fires. Never burn treated wood or painted wood, or wet wood. Keep the flue open so that you can let plenty of oxygen into. Add wood in small amounts and don't let the fire smolder. Do not use a fireplace indoors if you're in a smoke control area.

Make sure that your chimney and stove are correctly installed. Wood stoves that are not properly installed can ignite a fire in the chimney that could release harmful gases into your home. Regularly inspecting and cleaning the chimney is also essential. Check that the chimney flue is not able to leak, which can cause carbon monoxide poisoning.

It's a good idea keep your wood in a shed or Tarp. This will help the wood to dry out and grow faster. To minimize the risk of fire, keep the wood away from other heat sources. You should also put your stove on an inflammable surface like a tiled floor.

It is important to be sure to supervise your children around the stove, especially if you have young children. They may try to touch the flame or play with the hot ash which could be risky. It is recommended to keep all flammable items at least three feet from the stove. You should also think about installing a heat shield to protect walls and other surfaces from damage. It's also an excellent idea to have your family practice home fire drills. This will allow you to get out of your home in an emergency. For more information on how to keep your home secure, check out our article on escape routes to a fire in case of a house fire.